#Cisco u boot commands serial number
#Cisco u boot commands 32 bit
#Cisco u boot commands download

user-identity action domain-controller-down.PCI-e 2 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 2.0 PCI-e 1 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0 *** Warning - bad CRC, using default environment SF: Detected N25Q32A with page size 64 KiB, total 4 MiB

#Cisco u boot commands 32 bit

PCIe, Idx 2: Link upgraded to Gen2 based on client cpabilitiesĭDR4 Training Sequence - Ver TIP-0.23.(Sublib 0.8)0ĭDR4 Training Sequence - Switching XBAR Window to FastPath WindowĭDR4 Training Sequence - Ended SuccessfullyīootROM: Image checksum verification PASSEDīootROM: Boot image signature verification PASSEDĭDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled PCIe, Idx 1: Link upgraded to Gen2 based on client cpabilities

:** Link is Gen1, check the EP capability I don't have prog_pid in available commandīootROM: RSA Public key verification PASSEDīootROM: CSK block signature verification PASSEDīootROM: Boot header signature verification PASSEDīoardId = 0x23board SerDes lanes topology details: Please help me to set default profile in init Version - print monitor, compiler and linker versionīased on your reply, those stick out to me: prog_emblacklist- Program EM blacklistīut I see nothing related to the Board ID value. Verify_bl- Cisco Bootloader signature verify Ubifsload- load file from an UBIFS filesystem Tftpboot- boot image via network using TFTP protocol Temp - temp - Display the device temperature. Showvar - print local hushshell variables Saveenv - save environment variables to persistent storage Run - run commands in an environment variable Resetenv- resetenv - Erase environment sector to reset all variables to default. Rcvr - rcvr - Start recovery process (with TFTP server)

#Cisco u boot commands download

Prog_phyfw- Download and program PHY firmware

#Cisco u boot commands serial number

Prog_emserial- Program EM unique serial number Prog_emeeprom- Program EM EEPROM with raw binary data Prog_emcookie- Download and program EM cookie Ping - send ICMP ECHO_REQUEST to network host Phy_type- phy_type - Return PHY type at port index Phy_fw_down_to_spi- phy_fw_down - Downloads x3220/3310 Ethernet transceiver PHY firmware to spi. Phy_fw_down_to_ram- phy_fw_down - Downloads x3220/3310 Ethernet transceiver PHY firmware to ram. PciePhyWrite- pciePhyWrite - Write PCI-E Phy register PciePhyRead- phyRead - Read PCI-E Phy register Pci - list and access PCI Configuration Space Nfs - boot image via network using NFS protocol Netboot - boot Linux from network using TFTP/bootp Itest - return true/false on integer compare Ir - ir - reading and changing MV internal register values. Iminfo - print header information for application image I do see the following commands available: u-boot> helpīoardinit- Downlod and execute board initialization scriptīootd - boot default, i.e., run 'bootcmd'īootm - boot application image from memoryīootp - boot image via network using BOOTP/TFTP protocolīootz - boot Linux zImage image from memoryīubt - bubt - Burn an image on the Boot flash device.Ĭoninfo - print console devices and informationĭhcp - boot image via network using DHCP/TFTP protocolĭump_emserial- Dump EM unique serial numberįdt - flattened device tree utility commands Thanks for the reply, but the command is not accepted: u-boot> progpid 2k Is TAC/RMA the only option left here? I would very much like it if we were able to fix this ourselves. I see no option to set this, only to clear (via clear_board_env).Īs a side note, where is the documentation on u-boot? SF: Detected S25FL032P with page size 64 KiB, total 4 MiBĬompared that to a working AP (same model): u-boot> dump_board_envĮM Blacklist : pid=00000000, mask=00000000ĮM Whitelist : pid=00000000, mask=00000000

But after reload, power-cycle and even mode-button-reset it keeps getting stuck at the init> prompt.Īfter some poking around in u-boot, I noticed that the board_env variables are not set: u-boot> dump_board_env 2K (new) the AP boots normally and functions as expected (joins Controller, etc.). Please choose one of the following boards: We have a 2802i AP that keeps booting into init> prompt: init>